NITROUS OXIDE ( nos / n2o ) advice forum

Nitrous Oxide ( NOS / N20 ) Forum
 
It is currently Sat Nov 17, 2018 1:24 pm

All times are UTC




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Nitrous transducer wiring
PostPosted: Wed Mar 01, 2017 10:53 am 
Offline
Learner

Joined: Sun Nov 27, 2016 2:03 pm
Posts: 129
I want to lay in the wiring for a pressure tranducer from the Max extreme in the glovebox to the bottle in the rear, I can understand one of the wiring diagrams which shows the R1 12v supply and R9 nitrous pressure input but cant work out how the Max switches a relay for a bottle heater relay, are there any wiring diagrams showing this


Top
 Profile  
Reply with quote  

Advertisement

Wizards of NOS Nitrous Oxide Systems
 Post subject: Re: Nitrous transducer wiring
PostPosted: Wed Mar 01, 2017 1:33 pm 
Offline
Wizard
User avatar

Joined: Sat Mar 21, 2015 8:13 pm
Posts: 968
Location: Orlando, Fl in 'Merrrrica!
See this wiring diagram: http://www.noswizard.com/pdf/max_v2_wiring.pdf


Top
 Profile  
Reply with quote  
 Post subject: Re: Nitrous transducer wiring
PostPosted: Wed Mar 01, 2017 7:15 pm 
Offline
Learner

Joined: Sun Nov 27, 2016 2:03 pm
Posts: 129
Yes ive got that one printed out, but you may have to spell it out for me, I get it theres the 12v R1 output from the max to the sensor and the R9 the nitrous pressure input to the max, I get the 12v supply voltage from the arming switch to the bottle heater relay coil terminal 86 and then on that diagram the wire from terminal 85 of the relay goes to the ECU, thats the bit i dont get, what is that ECU and how is the max switching that heater relay when the pressure in the bottle gets to the preset pressure.

Sorry if im being a bit stupid?


Top
 Profile  
Reply with quote  
 Post subject: Re: Nitrous transducer wiring
PostPosted: Wed Mar 01, 2017 10:04 pm 
Offline
Wizard
User avatar

Joined: Sat Mar 21, 2015 8:13 pm
Posts: 968
Location: Orlando, Fl in 'Merrrrica!
LOL no you're certainly not 'stupid' I run into the same problems all of the time, trying to figure out how things work.

I see what you're saying about the pin 85 on the heater. In the diagram, it shows that pin to connect to the output wires on the Maxy and it can use either one: Output 1 [yellow L10] and Output 2 [grey L5]. Once the Maxy sees a low pressure on the bottle, it grounds either output, and in this case, it would ground the relay to power the heater. That's why the wires for the ground on the Maxy are so beefy: it can handle a lot of power. You can use the outputs for any number of accessories besides a heater.

I hope that explains well because I'm HORRIBLE at explaining things. :drunken:


Top
 Profile  
Reply with quote  
 Post subject: Re: Nitrous transducer wiring
PostPosted: Thu Mar 02, 2017 9:02 am 
Offline
Learner

Joined: Sun Nov 27, 2016 2:03 pm
Posts: 129
Ah yes all clear now, that Maxy certainly is a clever bit of kit, I may not fit a bottle heater straight away but wanted to install the wiring for a it if needed at al ater date


Top
 Profile  
Reply with quote  
 Post subject: Re: Nitrous transducer wiring
PostPosted: Thu Mar 02, 2017 12:59 pm 
Offline
Wizard
User avatar

Joined: Sat Mar 21, 2015 8:13 pm
Posts: 968
Location: Orlando, Fl in 'Merrrrica!
:yes:


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

  • Advertisement
Wizards of NOS Sparkplugs
Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group  
Design By Poker Bandits