NITROUS OXIDE ( nos / n2o ) advice forum http://nitrous-advice.org/ |
|
pressure gauge question http://nitrous-advice.org/viewtopic.php?f=6&t=5807 |
Page 1 of 1 |
Author: | joeh [ Thu Mar 31, 2011 6:51 pm ] |
Post subject: | pressure gauge question |
hi guys.....about to fit my won pressure gauge....does the 5mm nylon pipe connector seal when tightened to the t piece that is supplied with gauge or is there soething else i need to do...cheers |
Author: | teddybare [ Thu Mar 31, 2011 7:00 pm ] |
Post subject: | Re: pressure gauge question |
im pretty sure when i fitted mine that was it, just that little washer |
Author: | joeh [ Thu Mar 31, 2011 8:32 pm ] |
Post subject: | Re: pressure gauge question |
thanks mate....altho there was no washer unless it was already in place...just a gauge and t piece |
Author: | teddybare [ Thu Mar 31, 2011 9:07 pm ] |
Post subject: | Re: pressure gauge question |
oh have a look then, mine was loose in the box ... |
Author: | Noswizard [ Thu Mar 31, 2011 10:52 pm ] |
Post subject: | Re: pressure gauge question |
Some liquid sealer would help and full instructions are on our website - instruction manual page. |
Author: | joeh [ Fri Apr 01, 2011 12:36 pm ] |
Post subject: | Re: pressure gauge question |
used liquid seal from bottle side but when 5mm pipe goes ot other side of t piece if i use liquid seal will it not be difficult to remove when removing pipe |
Author: | joeh [ Sat Apr 02, 2011 3:55 pm ] |
Post subject: | Re: pressure gauge question |
any ideas guys......cheers |
Author: | teddybare [ Sat Apr 02, 2011 5:14 pm ] |
Post subject: | Re: pressure gauge question |
on pic 3 is were the little washer connected on to the gauge on mine.......http://www.noswizard.com/hpsnw_admin/pd ... ctions.pdf |
Author: | Noswizard [ Sat Apr 02, 2011 5:32 pm ] |
Post subject: | Re: pressure gauge question |
Full instructions for this job are here; http://www.noswizard.com/hpsnw_admin/pd ... ctions.pdf |
Author: | joeh [ Sat Apr 02, 2011 5:55 pm ] |
Post subject: | Re: pressure gauge question |
ive used thread seal between bottle and t piece and t piece and gauge....but what i need to know is do i need washer between male 5mm pipe and female end of t piece ? |
Author: | teddybare [ Sat Apr 02, 2011 6:04 pm ] |
Post subject: | Re: pressure gauge question |
i aint |
Author: | Noswizard [ Sat Apr 02, 2011 10:09 pm ] |
Post subject: | Re: pressure gauge question |
joeh wrote: ive used thread seal between bottle and t piece and t piece and gauge....but what i need to know is do i need washer between male 5mm pipe and female end of t piece ? As shown in the above instructions, the sealing washer is for the gauge and as stated in the above instructions, NOTHING additional is needed to seal a pipe connection. |
Author: | joeh [ Sat Apr 02, 2011 10:56 pm ] |
Post subject: | Re: pressure gauge question |
can you supply a seal on its own as i never received one with the gauge..cheers joe |
Author: | Noswizard [ Sat Apr 02, 2011 11:40 pm ] |
Post subject: | Re: pressure gauge question |
joeh wrote: can you supply a seal on its own as i never received one with the gauge..cheers joe The seal is VERY small and is sent in a small plastic bag in with every gauge and unfortunately it's so small that many customer misplace it or don't even see its there. However as it isn't essential and if the gauge has sealed by just using sealer it shouldn't be needed. |
Author: | joeh [ Sun Apr 03, 2011 1:46 am ] |
Post subject: | Re: pressure gauge question |
its the 5mm nylon pipe from solenoid that goes to the t piece im concerned about..does that need washer as i need that to be loosened when i have to remove pipe for bottle refil... |
Author: | teddybare [ Sun Apr 03, 2011 8:52 am ] |
Post subject: | Re: pressure gauge question |
noooooooooooooooooooooooooooooooo |
Author: | joeh [ Sun Apr 03, 2011 9:18 am ] |
Post subject: | Re: pressure gauge question |
lol.....okay say nothing req'd for the 5mm pipe connector...........got it....thats all i wanted to know...... |
Page 1 of 1 | All times are UTC |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |